3D modeling, not very detailed designing - 23/11/2020 11:44 EST

Painel de Comentários

• 
  Proprietário do Concurso

  • 4 meses atrás

  Thanks everyone.. This contest has ended.
  
  Hope to see you aging in another opportunity >>>

  • 4 meses atrás
  1. 

     hasankuet

     • 4 meses atrás

     Thank you

     • 4 meses atrás
• 

  rafihathbd

  • 4 meses atrás

  Check #13 will be waiting for feed back

  • 4 meses atrás
• 

  archshabbir

  • 4 meses atrás

  #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize #increaseprize

  • 4 meses atrás
• 
  Proprietário do Concurso

  • 4 meses atrás

  Don't hesitate to contact me on DM.

  • 4 meses atrás
  Ver mais 2 mensagens
  1. 

     hasankuet

     • 4 meses atrás

     ok working on don't close early

     • 4 meses atrás
  2. 
     Proprietário do Concurso

     • 4 meses atrás

     I'm already interested with your work.. Thanks Husain

     • 4 meses atrás
• 

  rafihathbd

  • 4 meses atrás

  Check entry #1 and inbox me if this is what you want. I have the obj file ready

  • 4 meses atrás
  1. 
     Proprietário do Concurso

     • 4 meses atrás

     I have commented on your entry..
     Thanks for your great work.
     
     There's also another 4 models, good luck brother. all the best.

     • 4 meses atrás
• 

  Rudolph07

  • 4 meses atrás

  hello, do you want to print this in parts or all in one solid?

  • 4 meses atrás
  1. 
     Proprietário do Concurso

     • 4 meses atrás

     Every piece of the 5 models should be printed individually Rodolfo.. Thanks for the feedback.

     • 4 meses atrás
• 

  guarco63

  • 4 meses atrás

  Hello, are you sure they use the appropriate 1000: 1 scale?
  Will the water tower be 4mm x 4mm x 13mm high in print?
  At that scale it is impossible to print the columns that apparently measure about 40 cm, which would be 0.4 mm in printing.

  • 4 meses atrás
  1. 
     Proprietário do Concurso

     • 4 meses atrás

     No, all measurements in Cm..
     
     Thanks for your comment & for clearing that up.

     • 4 meses atrás
• 

  arqfernandezr

  • 4 meses atrás

  #increaseprize

  • 4 meses atrás
• 

  AyerNielsen

  • 4 meses atrás

  This contest does not make sense and those plans are terrible to work off of.

  • 4 meses atrás
  1. 
     Proprietário do Concurso

     • 4 meses atrás

     Dear, it's as mentioned that the work accepted can be tolerated to less than the usual accuracy elsewhere
     
     It's over 200 years buildings, it's the only data can be provided for such project, I personally have done punch of them and I still work on them just from plans.
     
     Our work only care for representing the sites as accurate as possible, don't bother to go to the extreme
     
     It will be printed in 1:1000 scale if you can imagine

     • 4 meses atrás