Create 3D Model for printing from PSD logo

  • Estado: Closed
  • Prêmio: $240
  • Inscrições Recebidas: 35
  • Vencedor: yop1172

Síntese do concurso

Design a 3D model based on the logo PSD provided that can be easily 3D printed from STL format.

The model is going to be 3D printed quite large and used in our office. We can paint and texture the model once printed, so we're open to any colors or other ideas for the model as well.

The more detailed, creative or just damn cool the model created is the better.

Thanks for the early submissions folks.

The intent is for the 2D logo to be recreated in 3D with the ability to be 3D printed from an STL format.
3D Render and object can be in any program as long as an STL output can be provided.

It will be 3D Printed as a free standing object, like a trophy.

For more detail, the spray paint can should be rendered as a cylinder, the "D" logo can be dealt with in a creative manner of the designers choice. Either rendered as a label on the can that stands out, or carved into a hollow section of the spay can.

The paint dripping from the side of the can should be used as a stand for the model and a base plate for the model to stand upright should be added to the bottom of it. Perhaps the 3D paint dripping off the can is made to look like it is pooling on the ground as the base plate. The can itself should be rendered on an angle from horizon as it is in the PSD.

Thanks!

Habilidades Recomendadas

Feedback do Empregador

“Excellent designer, very responsive. Will absolutely work with again in the future.”

Foto do perfil mlegary, Canada.

Principais inscrições deste concurso

Ver Mais Inscrições

Painel Público de Esclarecimentos

  • govind14598
    govind14598
    • 2 semanas atrás

    please chek out entry no #55

    • 2 semanas atrás
  • bdas3d
    bdas3d
    • 2 semanas atrás

    Dear contest holder- Please consider the stability and weight of the model also ( center of gravity point should be inside the model), beside the aesthetic design .

    • 2 semanas atrás
  • Kindland
    Kindland
    • 2 semanas atrás

    Good luck printing that...

    • 2 semanas atrás
    1. keerthirajan25
      keerthirajan25
      • 2 semanas atrás

      Exactly... Countless support structure would ruin the surfaces while removing

      • 2 semanas atrás
  • MosTafa1Ramadan
    MosTafa1Ramadan
    • 2 semanas atrás

    Working will make better result

    • 2 semanas atrás
  • Devpro11
    Devpro11
    • 2 semanas atrás

    Since you want to model for 3d printing, I have prepared a realistic 3d printing file(stl).

    • 2 semanas atrás
  • Devpro11
    Devpro11
    • 2 semanas atrás

    How are you?

    • 2 semanas atrás
  • nanangkh
    nanangkh
    • 2 semanas atrás

    Please review #40

    • 2 semanas atrás
  • facefromdream
    facefromdream
    • 2 semanas atrás

    Maximum height with stand?

    • 2 semanas atrás
  • Kindland
    Kindland
    • 2 semanas atrás

    Hello @Contest Holder, do you want the Trophy to be made out of multiple pieces connected with keyholes, or one full watertight piece?

    • 2 semanas atrás
  • coc3dart
    coc3dart
    • 3 semanas atrás

    working

    • 3 semanas atrás
  • sharkfreelancer
    sharkfreelancer
    • 3 semanas atrás

    first, where will you use it.. on the wall or on the office as a decoration it's important to know

    • 3 semanas atrás
    1. mlegary
      Proprietário do Concurso
      • 3 semanas atrás

      It will be 3D Printed as a free standing object, like a trophy

      • 3 semanas atrás
  • banigandlapati
    banigandlapati
    • 3 semanas atrás

    I don't think you just need a extruded version of you logo. Please elaborate your requirement.

    • 3 semanas atrás
    1. mlegary
      Proprietário do Concurso
      • 3 semanas atrás

      I've added to the original description and above

      • 3 semanas atrás
  • Karimaziz1
    Karimaziz1
    • 3 semanas atrás

    what is size of the model you want?

    • 3 semanas atrás
    1. mlegary
      Proprietário do Concurso
      • 3 semanas atrás

      The model should be no less than 420mm in total height.

      • 3 semanas atrás
  • mlegary
    Proprietário do Concurso
    • 3 semanas atrás

    Thanks for the early submissions folks. The intent is for the 2D logo to be recreated in 3D with the ability to be 3D printed. For more detail, the spray paint can should be rendered as a cylinder, the "D" logo can be dealt with in a creative manner of the designers choice. Either rendered as a label on the can that stands out, or carved into a hollow section of the spay can. The paint dripping from the side of the can should be used as a stand for the model and a base plate for the model to stand upright should be added to the bottom of it. Perhaps the 3D paint dripping off the can is made to look like it is pooling on the ground as the base plate. The can itself should be rendered on an angle from horizon as it is in the PSD. Thanks!

    • 3 semanas atrás
  • kartikv1
    kartikv1
    • 3 semanas atrás

    Please check entry#6

    • 3 semanas atrás
  • fahryalw
    fahryalw
    • 3 semanas atrás

    do you have any design

    • 3 semanas atrás
    1. mlegary
      Proprietário do Concurso
      • 3 semanas atrás

      It is attached to the description

      • 3 semanas atrás
  • omar019373
    omar019373
    • 3 semanas atrás

    Please provide with me more details.

    • 3 semanas atrás

Mostrar mais comentários

Como começar com concursos

  • Publique seu concurso

    Publique seu Concurso Rápido e fácil

  • Receba muitas inscrições

    Obtenha Toneladas de Inscrições De todo o mundo

  • Premie a melhor inscrição

    Premie a melhor inscrição Baixe os arquivos - fácil!

Poste um Concurso ou Junte-se a nós Hoje!