Encerrado

Circuit Board and codee

Hey,

I'm looking currently looking for some one who knows circuit boards how they work and how to assemble them to make what I have added as a picture below. I am looking for them to work on radio frequency (ie like a wireless door bell or car key remote). the second picture below is what i already have including the button sensors for the main board. I will also need the code to allow the correct commands. as below

1. When button one on the transmitter is pressed , signal the receiver to tell the main board to spin the motor clock-wise until sensor two is pressed.

2. When button two on the transmitter is pressed , signal the receiver to tell the main board to spin the motor anti clock-wise until sensor one is pressed.

I will need the code and the boards made and delivered. the dimensions are restricted to 63mm length x 28mm width x 2mm height. or 30mm length x 30 width x 30 height.

Thanks.

Habilidades: Arduino, Programação C, Engenharia Elétrica, Eletrônica, Microcontrolador

Veja mais: record circuit board, printed circuit board research, disadvantages printed circuit board, hs code 85340000, circuit board component abbreviations, hs code for populated printed circuit board, circuit board hs code, circuit board component letters, f1 on circuit board, pcb identification code, circuit board component identification, printed circuit board layout service, job printed circuit board pcb, printed circuit board give advantage disadvantage, design circuit board india, solidworks circuit board, disadvantage printed circuit board, circuit board solid works, printed circuit board design forum india, circuit board cad

Acerca do Empregador:
( 0 comentários ) Sydney, Australia

ID do Projeto: #19760315

16 freelancers estão ofertando em média $154 para esse trabalho

Anthony989

Hello, I am Anthony from Sri lanka. I have 7 years of experience in the filed and I am very much interested in your project. Why you should hire me ? * As a full time freelancer I have my own PCB fabricati Mais

$140 AUD in 7 dias
(59 Comentários)
6.5
MUhammadt429i

I have long experience with 8-bit , 16-bit and 32-bit micro-controllers. I work with Microchip (PIC) , Atmel (AVR , SAM) , ST (STM) , TI (MSP) , Nordic (nRF52), and NXP (LPC) micro-controllers. I use KEIL IDE , Atmel S Mais

$333 AUD in 3 dias
(36 Comentários)
5.8
hayat38402

I am Excellent at the following:  Embedded C Programming.  VHDL/Verilog  Microcontroller like Arduino,RaspberryPi,FPGA, AVR, PIC and STM32.  IDEs like Keil MDK V5, ATmel studio and MPLab XC8.  IOT Technolog Mais

$155 AUD in 3 dias
(25 Comentários)
5.4
Itblast

I've worked for years to perfect the art of laying out a circuit board. So much that I've built an entire business handling projects for high-profile clients from concept to prototyping to production. Whether you need Mais

$155 AUD in 3 dias
(1 Comentário)
2.8
doughy515

I am an expericned electronic engineer for the past 6 years. I will be able to take your idea to a fully working prototype by doing the circuit design, PCB layout, firmware and even a 3D printed case if needed.

$222 AUD in 7 dias
(1 Comentário)
2.5
toanasahmed

Hello I ve my own Hackerspace and we are working on these kind of projects with great efficiency We are interested in this project and willing to provide the solution Contact me so that we can discuss this further Your Mais

$155 AUD in 3 dias
(3 Comentários)
2.2
beemf1633

I’m electrical engineer and i'm interested in your Project, and so I would like to offer my services. I will do your work according to your demand.I see you project carefully you are using servo motor for rotating.I ha Mais

$99 AUD in 5 dias
(5 Comentários)
1.5
eltonavieira

Hello I'm an embedded software engineer and I would like to hear about your project requirements to estimate how much effort is needed to complete the job. so I can adjust my bid to job complexity. Best regards

$220 AUD in 20 dias
(1 Comentário)
1.1
Provi11

I have about 2 years experience in Arduino C programming and written programs for many arduino and robotics projects. I have also written code for electric vehicle.

$40 AUD in 7 dias
(1 Comentário)
1.2
meer11

Hi, I am an Electrical Engineer by profession, an expert in MATLAB, SIMULINK, ARDUINO, AUTOCAD, CREO, etc I will provide a circuit board and code for your project. Also I will be available for any revisions needed. P Mais

$140 AUD in 7 dias
(1 Comentário)
0.0
divinedesignr

Hello, Hope you are doing great. Let’s get you some brief details of us. We are an Innovative Product Design & Development Company, specializing in designing products for Industrial and Mechanical Industries. Mais

$222 AUD in 30 dias
(0 Comentários)
0.0
rama20chandra

experience in embedded software development and Android application development for embedded systems industrial experience in running motors and communication between boards using Bluetooth module

$144 AUD in 10 dias
(0 Comentários)
0.0
samuelrvw

I can make fabricate the board and ship it to you. Also once you receive it you can test and if you require support (meaning if there is any bug fix) we can work together to get it up. I can work on the type of MCU tha Mais

$265 AUD in 14 dias
(0 Comentários)
0.0
janiru160

I can do it

$38 AUD in 3 dias
(0 Comentários)
0.0
rathinchandra999

I am a professional embedded system engineer. I have checked your drawings. I can easily design the required PCB for you. Please message me for further discussion.

$111 AUD in 3 dias
(0 Comentários)
0.0
AventurierWX0

Hello, I am a hobbyist in this field, I am currently working on a circuit board like this so I can provide you with reference work and I am willing to do it for cheap (under the bid amount if time is not a concern for Mais

$30 AUD in 5 dias
(0 Comentários)
0.0