Encerrado

I need help with coding for induction motor protection using Atmel

The motor protector counts with one LCD, 4 potentiometers and I'm using a Arduino Pro Mini for prototyping with Arduino IDE. And also a MOSFET. I already a the code written by myself but came to a wall where I don't know how to overcome.

The LCD shows which is the lowest voltage (undervoltage protection) and also the highest voltage (overvoltage protection) acording to 2 potentiometers. And also the voltage.

I can't use delay() since it pauses the program. When I use delay() it won't get to do anything. I use the potentiometers to set a time for when it bypasses the one of the voltage potentiometers to wait 0.5 to 5 seconds before switching off the contactor/relay ( contactors usually use 100 V to 240V) driven by a MOSFET.

The last Potetiometer (remember we have 4 of them, 2 voltage potentiometers and 2 timing potetiometers) is to set a time of 30 second to 5 minutes. This timing event is to keep the motor from turning on again right after its turned off, preventing possible damage. This product is going to be used with a induction motor that drives a pump in a water well.

To measure the voltage from 3 Phase 480 Volts is a bit challenging. Since I want to keep it cheap but very useful. I was thinking of doing this with voltage dividers and with transistors to switch from phase to phase (First reading 2 wires for 0.5 - 1 second... That would mean 3 readings).

Habilidades: Arduino, Engenharia Elétrica, Eletrônica, Microcontrolador

Ver mais: i need help to write one paragraph of three to five sentences about any topic in your paragraph using the vocabulary words from, i need help getting my book edited not much money, i need help from scientist, i need help from an engineer, i need help finding a shoes designer, i need help finding a manufacturer, i need help find worker, i need help designing my van wrap, i need help designing clothes, i need help designing a shirt, i need help designing a form, i need help advertising my website, i need apply coding and, phase induction motor control using pic, induction motor protection using microcontroller

Acerca do Empregador:
( 0 comentários ) Mexico

ID do Projeto: #15170663

24 freelancers estão ofertando em média $7260 para este trabalho

$7894 MXN in 10 dias
(189 Comentários)
7.5
$8333 MXN in 10 dias
(42 Comentários)
6.6
riki888vw

Hi, I have experience in electronics and Arduino developing. I can design and develop induction motor protection for you. It is important to scan 3 phase voltages and current in real time and turn on protection al Mais

$10600 MXN in 15 dias
(18 Comentários)
5.4
websat13

hello sir i am interested in your project. why dont use a vfd converter to control the 3 phases of the motor, i am working already on this project. we can discuss that in private chat. regards.

$11111 MXN in 30 dias
(39 Comentários)
5.6
Manux25

Buenas tardes me llamo Manuel, soy Ingeniero Mecatronico y Programador con experiencia desarrollando proyectos con Arduino, ESP8266 y PIC en diversas areas, puedes verificar mi perfil y ver que soy un Freelancer activo Mais

$4500 MXN in 5 dias
(32 Comentários)
5.0
$6666 MXN in 10 dias
(26 Comentários)
5.1
$8333 MXN in 4 dias
(26 Comentários)
5.2
$8333 MXN in 10 dias
(21 Comentários)
5.1
$7777 MXN in 10 dias
(27 Comentários)
5.3
gauravsharma132

Hi We have good experience with arduino and can help you in this project. Let's connect. -- Regards Gaurav Sharma

$6888 MXN in 10 dias
(18 Comentários)
5.3
AlexFaster

Hi. I can help you with your project. I'm a specialist in robotics field with experience more than 20 years. We can discuss your motor controller in chat. Best regards, Alex.

$7777 MXN in 20 dias
(4 Comentários)
3.8
bogdan2451629

Hello. I think I am the guy that you need becouse have more then 5 years expirience in programming AVR microcontrollers (on Pro Mini Atmega 328). I understand that code need to work without delays. I can do it. If you Mais

$10000 MXN in 10 dias
(8 Comentários)
3.6
kchakraborty

hello, I am an electronics and communication engineer with 4+ years of experience in embedded systems and programming. I can code the system as you described. for 3 phase connection voltage measurement it is good to u Mais

$6888 MXN in 10 dias
(5 Comentários)
3.3
Sunrit121992

We have our own Lab setup specifically for embedded systems and Electronics design..had already done some projects on power Electronics Labview microcontroller embedded systems and AutoCAD and also we r trained about S Mais

$4000 MXN in 3 dias
(1 Comentário)
1.7
prefectworld

HIRE ME DIRECTLY THROUGH THIS LINK [url removed, login to view] A multi-gifted, dependable and capable Exploration Essayist with a demonstrated capacity to Compose Scholarly Papers, Report Comp Mais

$3750 MXN in 2 dias
(1 Comentário)
2.0
phaheez

A proposal has not yet been provided

$4166 MXN in 7 dias
(0 Comentários)
0.0
bs505

Hello, How are you? I have read your project description carefully I am very interested in this project. I have a lot of experience in this type of work. I'm sure I can complete it on time with high quality acco Mais

$8333 MXN in 10 dias
(0 Comentários)
0.0
$10000 MXN in 15 dias
(0 Comentários)
0.0
$3881 MXN in 10 dias
(0 Comentários)
0.0
mahmoudsadat

Please i need more details on the project. i have worked with both atmel micro controllers as well as arduino before and i believe i can help you

$7777 MXN in 10 dias
(0 Comentários)
0.0