Em Andamento

Class A common emitter BJT amplifier

Class A amplifier Project

As part of an electronic system a common emitter class A amplifier is required to be designed and simulated using Pspice. This amplifier uses the BJT Q2N2222 that can be biased using one power supply of 18 volts DC. This amplifier feeds another stage with input impedance of 17k ohms. The amplifier should amplify a signal with frequencies between 210Hz and 50kHz. At the medium frequencies range the output signal is required to be 95 times larger than the input signal which is 7mVrms AC. The collector current at operating point ICq is of 10 mA. Nominal preferred values for components should be used and all calculations for component values should be shown.

Known values are here as shown:

Vin = 7mV RMS

Vcc = 18v

Lower cut-off frequency = 210Hz

Higher cut-off frequency = 50kHz

Output impedence (ROUT) = 17k ohms

Vout / Vin = 95

Collector current Icq = 10mA

The screenshot attached is roughly what the circuit should look like.

A screenshot of the schematic and the schematic itself are attached to the file.

What I need is somebody who can calculate the correct values of the components shown on the schematic send send me them so I can modify the circuit to give the desired output. Any questions please contact me, thanks.

Habilidades: Engenharia Elétrica, Eletrônica

Ver mais: class bjt amplifier, bjt class amplifier, bjt class amplifier output signal, bjt amplifier class, common emitter bjt amplifier circuit, class amplifier bjt, common emitter class amplifier, common emitter bjt amplifier, class common emitter amplifier, class common emitter bjt amplifier, class common emitter, class bjt output, bjt class, bjt amplifier project, class common emitter amplifier icq, common collector amplifier, project class bjt amplifier, amplifier class schematic, bjt, class amplifier schematic, bjt amplifier icq, bjt common emitter amplifier, what is be electrical engineering, vout, i need an electronic project designed

Acerca do Empregador:
( 0 comentários ) Aberdeen, United Kingdom

ID do Projeto: #569903

Premiar a:

vishaliitkgp

hi, your circuit is very easy. i can give you the solutions within 1 day only with the complete simulation results. thanks

$30 USD em 1 dia
(1 Comentário)
0.0

14 freelancers estão ofertando em média $61 para este trabalho

am10riz

I can help you out [url removed, login to view]

$50 USD in 2 dias
(4 Comentários)
3.0
mayyurp

I am Electronics engineer and can provide you values you required.

$30 USD in 3 dias
(0 Comentários)
0.0
sumairahmad

I have work experience with orcid pspice. I can help you.

$150 USD in 5 dias
(0 Comentários)
0.0
VKElectronics

piece of cake I do engineering and have a hot-shot russian electronics engineer I work with

$30 USD in 2 dias
(0 Comentários)
0.0
chetanfadnis

$200, completion within 1 days.

$200 USD em 1 dia
(0 Comentários)
0.0
amitsaturn

hi boss, plz refer my PM..thank u..

$40 USD em 1 dia
(1 Comentário)
0.0
makinmakin

See details in MB.

$35 USD in 2 dias
(2 Comentários)
4.5
madhankv2

i am a student of Electronics in [url removed, login to view] task is a simple one i will go for it....

$30 USD in 3 dias
(0 Comentários)
0.0
rmilan

Please check Your pm, thanks.

$30 USD em 1 dia
(0 Comentários)
0.0
Ellite123

Hi Please check PM. Regards

$80 USD em 1 dia
(1 Comentário)
0.0
maxonlyforyou

RB1=20k RB2=1k RC=1k5 RE=10 Ohm CE=150n CIN=COUT=4700n I don't need your money. Price calculation -- your story about why you made this project and story about electronics in your countr Mais

$30 USD em 1 dia
(0 Comentários)
0.0
zamroo

Hi, I am ready to work on it.

$60 USD in 5 dias
(0 Comentários)
0.0
idreesshahzad

Hi, I can provide the solution for this project

$60 USD em 1 dia
(0 Comentários)
0.0