Em Andamento

Common Emitter Class A Amplifier

The project is to design and simulate a common emitter Class A amplifier using PSpice.

Nominal preferred values must be used for components and ALL calculations for component values must be shown in detail.

A screenshot is attached of the desired circuit layout which must be adhered to.

Another screenshot is also attached showing the desired output trace, remember midband gain must be 95 and lower and upper frequencies must be 210Hz and 500kHz respectively.

This amplifier will use the BJT Q2N2222 that can be biased using one power supply of 18 volts DC. This amplifier feeds another stage with input impedance of 17k ohms. The amplifier should amplify a signal with frequencies between 210Hz and 500kHz. At the medium frequencies range the output signal is required to be 95 times larger than the input signal which is 7mVrms AC. The collector current at operating point ICq is of 10 mA. Nominal preferred values for components should be used and all calculations for component values must be shown.

Known values are here as shown:

Vin = 7mV rms

Vcc = 18v

Lower cut-off frequency = 210Hz

Higher cut-off frequency = 500kHz

Output impedence (ROUT) = 17k ohms

Vout / Vin = 95

Collector current Icq = 10mA

If you have any questions about this project please message me and I will reply ASAP.

Habilidades: Engenharia Elétrica, Eletrônica

Ver mais: class amplifier pspice, class amplifier, common emitter class amplifier, class amplifier common emitter, common emitter amplifier pspice, common emitter class, class power amplifier pspice, common emitter, amplifier common emitter power, common emitter amplifier, emitter class, class common emitter power amplifier, common emitter project, design class amplifier pspice, common emitter calculations, vout, electrical and electronics engineering, common questions, common current, be electronics engineering, power common emitter, pspice common emitter cut, pspice class amplifier, design common emitter, project common emitter amplifier

Acerca do Empregador:
( 0 comentários ) Aberdeen, United Kingdom

ID do Projeto: #584934

10 freelancers estão ofertando em média $93 para este trabalho

adipdutt

i am enclosing two files of the design, if you are interested, please pay in escrow and i will transfer the value and design guidelines 1 had to put in one cap and one resistor. IC=9.88mA Vc=8.115 peak outp Mais

$150 USD in 0 dias
(3 Comentários)
3.0
jayasundarak

I can do it for you. In fact I make my students do this kind of amplifier design every year for their undergraduate level 3 subjects including the simulation, schematic design and PCB design. I will supply you with a g Mais

$100 USD in 4 dias
(0 Comentários)
0.0
mcernaianu

Good day! I am a PHD student in the field of Electrical Engineering. I am very familiar with Spice simulation and I am able to do the job with the calculation for component values. I frequently use LTSpice for simulat Mais

$70 USD in 3 dias
(0 Comentários)
0.0
saliah2003

hi; Contact me I can do this for you. Regards

$100 USD in 4 dias
(0 Comentários)
0.0
tipu04

Hi i can do this project for in Altium , i can do simulation for it in Pspice with in Altium.

$85 USD in 5 dias
(0 Comentários)
0.0
zamroo

I have 8years experience in electronics field. So i can do in any circuit simulation software.

$80 USD in 7 dias
(0 Comentários)
0.0
debasis007

I am an Design Engineer for an reputed Semiconductor company having ~3 years experience in Analog and Mixed Signal Design, Layout and Verification.

$100 USD in 2 dias
(0 Comentários)
0.0
sumairahmad

Dear, i have work experience with Orcad (PSpice). I already have done similar projects during my studies. I can help you in best way. You will get very good results from here. Thanks

$150 USD in 2 dias
(0 Comentários)
0.0
rmilan

Please check Your pm, thanks.

$30 USD em 1 dia
(0 Comentários)
0.0
makinmakin

See details in MB.

$60 USD in 2 dias
(2 Comentários)
4.5