Em Andamento

DCDC Converter Analysis and Design

Analysis and Report of Converter Schematic with Proffessional Report

I need to design a voltage controller and current and converter in PSim for a dc-dc fully isolated converter and a simple boost converter where the controller parameters are checked , analyzed , tuned and chosen. Matlab, Matlab toolboxes and or simulink should be used for this process.

There should be closed loop voltage control design (where necessary, with PI blocks, filters, comparators, voltage sensors, voltmeters, ammeters etc.) with reasons for block use and analysis on Control design. The circuit should simulate correctly with minimal ripple and smooth outputs. For the control design, where necessary, please include a Vreferecnce, error summer, pi block, and the gating signal should be appropriate with the reason for choice. I require a transfer function for the controller and converter with variable descriptions and component relation to variables in transfer function.

I will give the spec on acceptance - they are kV converters. Design the converters for OPTIMUM efficiency and show calculation overall efficiency with Pin and Pout Values; also design for lowest losses with reason for use of components and how they increase efficiency of reduce losses.

I'm trying to do an investigation looking at installed power in the semiconductors, size of passive components, evaluation of losses in semiconductors, losses in magnetic components and overall efficiency (so I need all these results with calculations, equations and reasons for use). The magnetic losses of the converter should be calculated with equations.

Require files to be saved in PSIM 9.0. If you require reference papers for assistance, I can attach them as well. and a start as soon as possible. Figures should be copied from clip board as a bitmap file and analysed and explained. The report template will show and example. Stresses, losses, installed power etc. analyzeD. Need all files Psim, word and MATLAB.

I have completed the circuits and need to check for optimum efficiency and output and operation. I require the equations to be laid out in the format shown in the template.

PSIM and Matlab to be used.

Will send attached file on acceptance.

No time wasters please!

Habilidades: Engenharia Elétrica, Formulários Eletrônicos, Eletrônica, Matlab and Mathematica

Veja mais: how to design circuit, design with magnetic, design analysis report, dc design, component board, circuits design, boost converter circuit design, example cdr report excel, example summary report research paper, free example roi report format, aspnet example cristal report, example aging report, crystal report graphics cut series, example crystal report, example crystal report aspnet, example spss report, example project report online examination system

Acerca do Empregador:
( 7 comentários ) London, United Kingdom

ID do Projeto: #10498867

Concedido a:


I am a senior year student in Gik Institute where I am serving as the president of the Giki Robotics Team. The team comprises of engineers with wide skill set including PCB designing, Micro-controller interfacing, Auto Mais

$25 USD em 3 dias
(0 Comentários)

9 freelancers estão ofertando em média $94 para esse trabalho


I am an Electrical Engineer having specialization in Electronics and Control, teaching in Electrical Department at FAST National University Pakistan. I am also persuing my MS degree in Electrical Engineering with speci Mais

$250 USD in 3 dias
(172 Comentários)

-----------------------------Best Result in Time & Professional Matlab Developer---------------------------------

$50 USD em 1 dia
(131 Comentários)
$24 USD em 1 dia
(9 Comentários)

Hi! My name is Fernando Téllez. I am a senior year student of electrical engineering at Universidad Simón Bolívar (USB), one of the most prestigious universities in my country (Ranked 34° at the QS University Rankings: Mais

$80 USD em 1 dia
(21 Comentários)
$138 USD in 2 dias
(14 Comentários)

Expert quality work will be provided in optimum time. THANKS Mais

$150 USD in 4 dias
(10 Comentários)

I’m a young engineer , working in electrical engineering and electronics industry since 2009. Embedded programming of Atmel microcontrollers' since 2010. Development of applications in C++ Java, MATLAB - since 2011 Go Mais

$40 USD in 5 dias
(9 Comentários)

Electrical engineer with experience in power conversion and power converter topologies. Direct experience in wind turbine industry and power supply design. I have simulated a wind turbine in both PSIM and Matlab for So Mais

$116 USD in 3 dias
(0 Comentários)

A proposal has not yet been provided

$25 USD em 1 dia
(0 Comentários)