Concluído

PCB Layout

We need this job done in 1 day.

The schematic was done with Orcad Capture 9.2.3

There is a total of 33 unique components with 163 component placements.

We will require a signed NDA before releasing the files.

The person that is awarded this job will be provided with all datasheets, the schematic and BOM.

1. The board cannot be any bigger than 3”x5”

2. Place all components on one side.

3. Place 4 non plated mounting holes 1/8” x 1/4” from corners of board.

4. Hole dia (115 mill) to accommodate a #4 screw (Spec sheet included in datasheet zip file) to ensure screw head does not overlap components.

5. Any components that can build up heat, please add copper pour, and use pin wheel (thermal relief) style pads for any through hole soldering connections.

6. Make sure there is no silkscreen over the top of VIA’s, and no silkscreen on any pads.

7. 20mil minimum annual rings required for all through hole components

8. All components that connect to ground, or solder pour, please use pin wheel (thermal relief) style pads to assist with through hole soldering.

9. Min hole size .015”

10. Min trace distance between traces 8mil.

11. 2oz Copper finished

12. All DC Power traces to be 25mil Min and spaced at least 15 mil apart

13. All AC power traces to be 40mil Min and spaced at least 15 mil apart

14. The following 2N6497 locations Q1,Q2,Q3,Q4,Q5,Q6 may have clip on heatsinks, please lay them all out side by side so we can use a custom heat sink bar across all of them.

15. Fabrications Notes below should show on the drill layer:

Board Name, Rev

Material: FR4, 0.062” +/- .007

Type: DSPTH, SMOBC, HASL Free RoHS Compliant

Plating at finish 2oz

Silk Screen White Epoxy

Tolerances are in inches

Holes: +/- .003 (after plating)

Route: +/- .005

Habilidades: PCB Design and Layout, Circuit Board Layout, Layout PCB

Veja mais: wwwcircuit power supply pcb layout circuit operation, simple volts regulated power supply pcb layout, volts power supply pcb layout, pcb layout design rules, pcb design online, pcb layout software, pcb board, pcb design steps, pcb layout diagram, pcb layout design, pcb design basics, power supply circuit pcb layout, free power supply pcb layout design, pcb layout volt power supply, pcb layout recommendations small power supply, variable power supply pcb layout, dc janakpuri electronics project report pcb layout, pcb layout power led, power ethernet pcb layout, power supply pcb layout eagle

Acerca do Empregador:
( 2 comentários ) homosassa, United States

ID do Projeto: #26782835

Concedido a:

Andrii0125

Hi. I have read your project description very carefully. I am a professional PCB designer with rich experience over 10 years. I will finish your project in a day perfectly. Best regards, Andrii.

$20 USD em 1 dia
(8 Comentários)
4.3

5 freelancers are bidding on average $50 for this job

hudex

Hello, I am an electrical and electronics engineer and pcb expert . I can solve your problem . I have vast knowledge of it and can do your task Thanks. Waiting to hear more

$30 USD em 1 dia
(14 Comentários)
3.3
saddamgul842

Hi dear I am an electronics engineer and I have industrial experience of power electronics circuit and PCB layout designing. I can design a PCB layout up to 16 layers. I did read your project description and i can prov Mais

$100 USD em 1 dia
(5 Comentários)
3.3
etalhak

Helllo, I am an electronics and telecommunicaiton engineer and I am quite experienced with hardware design. So far I have designed many single/multi layer PCBs. So I am sure that I can help you with your project. Do yo Mais

$85 USD em 1 dia
(2 Comentários)
1.7
TechNiv1

Hello I can do this job in a day. Ii have 7 years of experience in pcb design and layout, I have worked on so many design

$15 USD em 1 dia
(0 Comentários)
0.0