Remote power control over ethernet

Hi there,I'm biddin on your project "Remote power control over ethernet"Microcontroller, Electronics, Electrical Engineering, Circuit Design and PCB Layout I'm looking for a PCB design to control consumer motherboards over ethernet I have read your project description and i'm a Professional Engineer therefore i can do this project for you perfectly.I still have a few questions. please leave a message on my chat so we can discuss the budget and deadline of the project. Thanks. .. .

Best PCB Design Expert at your doorstep! Dear Client, We can control, consumer motherboards over ethernet for a PCB design We couldn’t stop ourselves from bidding after going through the description as they are an exact match with our skill set and experience. We have experience in Remote power control based PCB design and know all the intricacies required to get the job done with perfection. With more than 15 Years of experience in PCB Design and Circuit Design in Altium, We can ensure you best quality work and before time delivery. Following is a brief list of expertise that we are carrying: 1. IOT products development 2. Microcontrollers based circuit design – STM32, STM8S etc 3. Smart Products like Smart watch - GSM/GPRS/GPS etc 4. Wireless Products - BLE/WiFi- ESP32/ESP8266/NRF24L01 5. Low Power Battery Products design – Rechargeable and Non chargeable 6. Power Electronics – Buck, Boost, Flyback etc 7. RJ45, Remote Power, Ethernet, Motherboards Please answer the following questions: 1 What are your future plans with this project? 2. Are there any specific market standards like CISPER you are aiming? 3. What will be ambient temperature of this product? 4. Are there any other specific requirements besides the ones you mentioned Let’s have a quick discussion for 5 mins where we would formulate a plan of action of how we shall take this project to the horizons of success. Regards Avi Tech Experts Quality is never an Accident

Hello, thank you for your job posting. I read your description about--PCB I am a senior electrical engineer. I have plenty of experience in firmware development and micro-controller developments. I can write the firmware based on Arduino, Raspberry Pi, Pic, Atmega, FPGA, ARM, DSP, PLC and so on. And I can design the circuit by the Altium, Eagle, KiCAD, Allegro & OrCAD, PADs. I provide the services - Gerber files, Netlist generation, BOM generation and 3D Models of PCAD and ECAD. I am also good at AutoCAD, Solidworks. And I can simulate all circuits with Proteus, LT-spice, Matlab, Simulink, Multisim, and Labview as well. Due to my experience in firmware development, I will bring you the perfect result in time with high quality. I will also give you a detailed explanation of the process. Looking forward to hearing from you soon Thanks

Hi. I am a professional PCB designer with rich experience over 10 years. Please let me discuss about your project in detail. I will keep good communication with you for discussing. Best regards, Andrii.

Hello, Dear. I am an electronic engineer and PCB designer. I have experience of upgrade designing jetson nano board for 10 GBps with PCIe connector.. And I have experience of designing 16layers motherboard. I can deliver you high quality design. Thank you.

Hi, I am electronics engineer and have experience of schematic and PCB design, I can do your task. Inbox me for your task

Dear Client, I can control, consumer motherboards over ethernet for PCB design I have read and understood your requirements and could do it for you in the least time and utmost superior quality. I have experience in Remote power control and could design it for you as per your requirements. I am having more than 15 years of experience in PCB Design, Circuit Design, Circuit simulation, IOT products development and building electronic products. The expertise of mine is in the following fields: 1. Wireless Products – BLE, Wifi, NFC, LoRa etc 2. Power Electronics- Buck, Boost, Flyback, Half Bridge etc 3. IOT sensors interfacing – Pressure, Temperature, Moisture, PH etc. 4. Microcontrollers- ESP32, STM32, STM8S, RL78 etc. 5. Ethernet, RJ45, Buttons, LEDs, 8 pin header After reading your project details, I have certain queries and suggestions: 1. What is the application of this product? 2. What will be ambient temperature of this product? 3. What are the mechanical constraints to be taken care of? 4. What are the standards that the product would be complying to? 5. What are the user protections required for this project? Please try to answer these questions based on which I would be providing free of cost consultation. I am new to this site but I am an expert in electronics product development. Please message me so that I can formulate a success plan for this project. Waiting for your reply, Regards Hari Mohan Engineering for one is a magic for others

Hi. I'm professional programmer/electronic hardware developer with experience over 20 years. I implemented many M2M devices with different interfaces, Ethernet one of them. There are different ways to create such device, we can discuss all details in chat. Regards, Alex.

Hi I am Electrical and Electronics Engineer with 14 years experience in micro controller programming and PCB design. I can develop a custom PCB design and develop firmware and provide a working prototype including all design files. We can discuss how it will be done Regards Senthil Chennai, India

Hi I am an expert with more then 6years of experience in IoT, Automation, Embedded Systems, pcb design and dovelopment and prototyping. I have hands-on experience in arduino, esp32, pic, arm, raspberry pi and other mcu. Thanks

Hello Dear Concern, We are a team of professional members of Electrical, Electronics, Telecom, Mechanical, Civil, Chemical, Energy, Industrial Engineering. We are also expert in following softwares: Embedded system, PCB DESIGNING, ARDUINO, ESP, MATLAB, Simulink, PADS, PORTEL,Proteus, Cadence ,Solidworks PCB, ANSYS, ABACUS, AUTOCAD, DipTrace, Kidcad, MATLAB, SPSS, PRO/E, CATIA V5, Stud pro, Homer Pro, We are trusted people and will never break you trust. We will deliver your work with in your defined timeline. I assure you that your work will be error free and 100% professional with high quality. We will never waste your time and money. We will try over best to make you proud. Please consider me for this job. Thank you in advance. Regards,

hi i have 13 years experience to develop embedded system for lab and industrial system my profile show you my experience please visit that already this project in LPC and STM32 ARm microcontroller thanks

I'm a professional Software Engineers and Electrical engineers. with over 10years experience in Universal Circuit, Simulator (QUCS),PCB Layout, Arduino and have been working on Industrial Automatics and Electronics. my fields of interest are Schematic design, Prototyping, PCB, xenforo, HVAC, LTE system model, Thermal system design, FPGA, Verilog / VHDL, Matlab/ Simulink, Microcontroller, Design, Multisim, SLD Layouts (Single Line Drawing), Hire me for an outstanding and excellent work. I promise to put a smile on your face and give you a wow effect.

Hi, An interesting project, "Remote power control over Ethernet". This is something I'm doing right now in another project where I uses both cabled and wireless technologies. I have also a lot of questions and ideas in how to take the product to the next level. I´m also an IT pro in the infrastructure are (network and servers) and we could discuss if a IPMI solution with PoE is a solution that could fit your needs or if that is to feature rich.