Solidworks scissor trabalhos

YOUR RESPONSE must be specific to your experience with Geometric Dimensioning and Tolerancing (GD&T) drawings for electric motor manufactures. If you send me a generic reply speaking to anything other than electric motors I will not consider you or your firm. We are looking for a freelancer who can work with our engineers to take our Solidworks models and assemblies and produced detailed manufacturing drawings specific to the BLDC Motor market. The engineer must have experience with BLDC motors and respond with specific information about their work producing BLDC motor drawings with the required specifications for manufacturing and assembly.

Please Read CAREFULLY! We Make Inclined lifts, Hillside Lifts, (there are several names for these things!). WE NEED the Rail and its components created using the rail profile from our survey information. We need a Skilled SOLIDWORKS User with Engineering Knowledge to follow our instructions and ask Intelligent Questions. The Profile is created using the Geometry of the Chassis which runs along the rail, WE PROVIDE THIS GEOMETRY! We have 3 types of Rail. Some examples of our work are shown in the attached pictures Please study the attachments We will base our selection of 1 or 2 Freelancers on the feedback from the information attached. We will require an example of work from the successful applicant/s This is continuous work, we will install 2 sets per month.

Hi looking to get the attached projects done. Have a look and see what you think. Need them done in solidworks. Thanks

I’m looking for Solidworks designer to design a robotic arm and then do stress test & finite element analysis

NEED SOMEONE FOR AN SMALL URGENT SOLIDWORKS TASK

Kinematic, kinetic analysis in SOLIDWORKS

Height from ground to feeder is 4600mm. Quantity of steam generated (output) :9 TPH Quantity of coal consumed (Input) : 1.6 TPH need design calculations of this conveyor belt and Solidworks cad file of it. the safe material for the job and write the proper reason why you used it. the estimated value for the manufacturing of the job. calculate the motor specifications required for the conveyor belt. For the Calculation of CB refer the pdf given below and the Pictures attached Project to completed before 02-05-2022 or 03-05-2022 (Indian Standard Time)

...following plans: • Kenworth Cabin Air Filter Assembly Top • Kenworth Cabin Air Filter Assembly Left Side Plate • Kenworth Cabin Air Filter Assembly Bottom and Outlet Side • Kenworth Cabin Air Filter Assembly Filter Box Assembly page 1 of 2 • Kenworth Cabin Air Filter Assembly Mounting Bracket 2 • Kenworth Cabin Air Filter Assembly Mounting Bracket 4 The existing models are SolidWorks 2021. We need the finished files to include SolidWorks models, PDF drawings, and DXF Drawings. We have included a packet of the hand-drawn notes of each drawing that needs alterations, as well as all DXF, STEP, and PDF files we currently have on this housing. Here are the changes we need to the files listed above: On “Kenworth Cabin Air Filter Assembly Top...

Hello, I am looking for a solidworks/CAD designer to create a 3D design replica of a vintage public seating bench (specifically, Friso Krammer Olympic 1200 - see attached photos). The bench has 2 components: 1) fiberglass/plastic molded one-piece seat and back rest (dimensions: 120x40x50cm) 2) aluminium cast leg (2 per bench - exactly the same). I am seeking a designer to create the 3D CAD/CAM model of the plastic seat and legs so I can produce a new prototype with minor modifications. Thank you for your consideration. Jeff

I have 5 pictures, I need to create solidworks (max 2015) model. We then create with laser cut metal sheet. We then make them paint sabloons to paint items. There is now info file where is basic info and picture files (one is coming later - Dog).

Steelwork design completed in Solidworks for an Inclined Lift. We need fabrication drawing for the various rail sections and columns to be extrapolated from the complete 3D model. Fabrication drawings will need to be in keeping with industry-standard guidelines regarding layout and annotation.

Produce Solidworks files ready for manufacturer from supplied pdf drawings.

Es una plataforma de cursos de capacitación para Solidworks

Design a prototype robot to measure a ceramic component used in a jet engine combustion chamber. The component is fired Alumina and is 52mm in diameter and 75mm height...trolley of 24 parts, into the measuring station, and back to another accepted trolley. Use off the shelf electronic and mechanical parts, RS Radionics, Farnell, Mitsumi, other makers sites etc. Determine all parts such as stepper motors, stepper drivers, PLC or raspberry pi, Arduino, sensors, mechanical sliders and rails, grippers, measuring head, power supply. Create developmental drawings in SolidWorks and a Bill of Materials for the project. Estimated cost required Indicate any further work required. No coding required but do consider and document how it will be programmed. Most experienced designer gets the j...

I will provide the STEP files of Solidworks model. Need help with simulation in simscape.

I need a 3d design for a robot drummer in SolidWorks / Inventor. A slider crank system must be placed on a drum. A drumstick must be placed on the slider crank. I have schemes and a piece already designed as inspiration, but any idea is welcome for a better result.

I require a .DWG being turned into a Revit model with all contours, features and views. This model will then be imported into Solidworks to design our lift system. The turn around time is very important.

Hi Umair A., I noticed your profile and would like to offer you my project. We can discuss any details over chat.

Perform a pick and place robot (design in solidworks and simulation in simscape)

Perform a pick and place workflow with robotic manipulator (design in solidworks and simulate in simscape)

We need the design of two brackets modified slightly. The existing models are SolidWorks 2021. We need the finished files to include SolidWorks models, PDF drawings, and DXF Drawings. Here are the modifications we require: PART#1376272-Add 4 inches to lower formed portion for a total of 15.5 inches. Add another Slot to lower portion. Extend slots to fit in extended 4 inch lower portion. Reduce over all length to 7.99 inches. Lower formed leg should be 4.91 inches. Part#1376262 Changes- Shorten formed leg to 4.4. Shorten Overall length to 16.45. We need these files in PDF, DXF and SLDPRT format.

Por favor, Cadastre-se ou Faça Login para ver os detalhes.

Convert 3D scan (.stl file) to 3D drawing in Solidworks (SW 2022 or older). This is not for manufacturing but for engineering products with this cilinder: - 3D draw the outside of the cilinder with as many nominal dimensions as possible. - Put the standard DIN912 socket head cap screws in the drawing, these of course do not have to be drawn in 3D. - Also draw the hydraulic connection holes on the cylinder head. This will be needed later to draw in hydraulic couplings and hoses. Draw these as tapped holes without the plugs as in the 3D scan, so that I can easily adjust them with the hole wizard. - On one side of the cylinder there is an o-ring, on the other side it has been removed for scanning. Draw the situation without the o-ring on both sides. - Make sure that the 3D drawings ar...

I have a full SW model of an electric bicycle. I require a number of the existing models to be changed [example: 27.5 inch wheel made smaller to 24 inch] I then require a new simple frame to be made to mount existing component models from the master, and a new front suspension. I only want to achieve a concept layout at this stage but it must be accurate. Please respond ONLY if you are an experienced mechanical engineer. I will send all details to a short list of applicants for full study before committing.

Kitchen drawings and design using Solidworks.

I am simulating the combustor from this paper, I would like simulation that can be validated with the paper my desired case is OFO45 with equivalence ratio = 0.9, and also i want the geometry to be made in solidworks and imported into ansys fluent

I need to learn full solidwork and CATIA as per the

I am a software project manager and not familiar to Solidworks. I am also open to another collaboration with right candidate. This is long term relationship. All candidate should be available to proceed video call.

New Spoon die development. spoon modeled in Solidworks along with forming dies

Good evening My work is fault injection in automated systems, in my case I have a simulation of a scissor lift in Simulink program (I will attach the link of the simulation below) What I want is to make a block with listeners, specifically I want four listeners, the 1st listener whenever realizes the scissor lift goes up (when it goes up it gets the message "going up". The 2nd listener wheneverrealizes the scissor lift goes down (when it goes down it gives the message "moving down". The third listener to perceive the Rate of change of the system movement and to output it as a result of a message similarly in, m/sec. I want the fourth listener to understand where the lift is, if it is down, up or somewhere in between and again to output the messages ...

Hi, there I have rough handy sketch. I am going to manufacture this product. So I need solidworks models and 2d drawings for manufacturing.

In the attachement, you find a 3D CAD file, c...this part in the drawing, where one length is different. Use the given STEP file above to create all three variants of the part. What I need: - The STEP file with the whole assembly - A STEP file of each single part of the assembly (use the names, given in Sketchup) - A DXF drawing of each part for manufacturing (use the names, given in Sketchup) - The original file of your CAD system (Creo, Solidworks etc...) - A short description, how you did this conversion If you can't upload the files at freelancer because they are to big or because they're not accepted, make a dummy entry. I'll contact you then and tell you where to upload your files. If you do a good job, I'll have more jobs like this for you in the future....

I have a mesh file of a root system (.obj), but when you load the file in solidworks (screenshot attached), the surfaces of the roots are not entirely connected and the surface is not smooth as well. I want to make the surface smooth and fill up the interior of the roots so that the cross sections are solid and ready for 3D printing. The other attached picture shows an example of what I wanna do. The upper part is the loaded mesh file, the lower part is the model ready for printing after making the surface smooth, removing some fine roots and making the cross sections constant (no need for that in my case).

Design and analyasis required for project pic given to reference

Hi, I have a Solidworks step file, I want someone to render the file in Blender like it is viewed in Solidworks. I am looking for someone who is good with Blender or any other software. I just want the model in gltf format rendered like in Solidworks. I also would like a screen recording of the work done on how to do it after project completion.

We are an aluminium guttering company based in Donegal, Ireland. We require a freelancer to draw our products in Solidworks in 2D & 3D for use on both our website and in various printed literature. All drawings should be to scale - CAD drawings can be provided. We'd also like some of the products to be photo realistic

I need a CAD engineer, who is able to draw technical 2D and 3D engineering drawings of battery pack box in solidworks or AutoCAD. He should be able to make a clean 3D model of the product. He should also be able to make project framework and submit final 3D model in STEP file. Job is to only draw in CAD software and make a 3D model of the product.

We are in need of a tech that can work by the hour to help my company install a computer and sensors while working on a scissor lift on a device that is 13 foot high. It will take about 20 hours of work time and will require the person to be onsite at the location. Please quote hourly rate and we will pay travel costs. Due to Covid you must be a resident of Hong Kong.

Needing someone to set-up solid works for our company. Templates models, prints linked to the models.

Looking for best way to design seat foam and seat covers. Also would like to be able to get flat patterns from the seat covers in dxf format so we can send them to our new pathfinder cutting CNC. Working in the boating industry. Would also like a,b,c,d size prints set up and linked to models. Starting a new job and they do not have solid works and nothing is set up yet. Need advice on how to do this. Maybe even PDM advise too. Since this is all new w really want to do this right from the beginning.

I have STL scan data file for a simple tank I want to reverse engineer it using geomagic design x or solidworks The part is simple.

I need mechanical engineer with background of the matlab and solidworks skills

Hi Anuroop K., I noticed your profile and would like to offer you my project. Can you do something for me in Solidworks? A new design for a mop wringer made from images and dimensions.

Hi Vishal K., I noticed your profile and would like to offer you my project. We can discuss any details over chat. Can you do something for me in Solidworks? A new design for a mop wringer made from images and dimensions.

Hi Mohamed K., I noticed your profile and would like to offer you my project. We can discuss any details over chat. Can you do something for me in Solidworks?

Hi Michael A., need a quote please. Have drawings in SolidWorks, number of parts want to make in China. Need to 'convert' drawings to plain English. (tolerances, surface finish etc) so that Chinese guys can read. I will need an invoice from you to release the funds. Thanks, Oleg.

The prototype is to be discussed once you agree to work on this project and sign a confidential agreement to ensure my idea isn't compromised. It's kind of research and development projects this project only take around 2 hours to be completed I’m looking for newbie designer who passionate to learn state on art of solidworks

Create 3D and 2D Solidworks drawings of RVS pulley holder. Is is not a precise part, just nominal dimensions are ok. A brass bushing is pressed into the square block.

You can use solidworks or autocad or doesnt matter.I want to get price for you.

Modelling an object from 2D (in illustrator) into Step format for posterior construction in CNC (wood). Software can be Solidworks, Solid Edge or Fusion 360.